In daily life, we will inevitably encounter some unexpected situations. For example, the toilet is too long and the cover is broken. At this time, we must be at a loss. We ca n’t repair it. We can only call a professional to repair it. Today I will introduce the toilet cover installation techniques.
Toilet installation steps:
(1) Take out the pipe plug of the ground drain, and after checking that there is no debris in the pipe, clean the pipe around.
(2) Align the water outlet of the toilet with the outlet of the sewer, lay it flat and straighten it, draw a mark on the bolt hole of the toilet, and remove the toilet.
(3) Make a hole with a diameter of 20 mm and a depth of 60 mm at the mark, insert a 10 mm diameter bolt into the hole, twist it with cement, place the toilet eye on the bolt, and make it fit the mark. After the test, The toilet is removed. Put putty around the toilet water outlet and the sewer pipe, and then align the four bolt holes of the toilet with the bolts, lay them flat and straighten them, put a rubber pad on the bolts, screw on the nuts, and tighten to a proper tightness.
(4) Align the center of the rear end of the toilet, draw a vertical line, draw a horizontal line at a height of 800 mm from the ground, draw a mark on the horizontal line according to the position of the two side holes on the back of the water tank, and punch a diameter of 30 mm and a depth at the hole 70 mm holes. Insert a bolt with a diameter of 10 mm and a length of 100 mm into the hole and twist it with cement. Hang the back water tank on the bolt, level it for alignment, especially to align with the center of the toilet , put a rubber pad on the bolt, screw on the nut, and tighten to a proper tightness.
(5) When installing the backwater tank elbow, first remove the nuts of the backwater tank inlet and the toilet inlet, back-to-back sleeves on the elbow, and rubber pads on the sewer pipes respectively. Insert the upper end of the drain elbow into the drain outlet of the back tank, and insert the lower end into the toilet inlet, then push the rubber pad to the nozzle, screw on the nut, straighten the elbow, and use pliers to tighten Moderately.
(6) When connecting the water supply with a figure eight gate, first measure the size of the water tank float gate from the upper water pipe mouth, match the short section, install the figure eight gate, and enter the upper water pipe mouth. Cut the copper tube or plastic tube. If you need the lamp fork, you should bend the girl, and then put the float door and the figure eight nut back to back on the copper tube or plastic tube. Insert into the entrance and exit of the drift gate and the eight-character gate, and tighten the nut.
The above are the simple steps to install the toilet cover , don't you know? I hope it will help you.
More articles:
Top ten faucet recommendations for faucet shopping guides
Faucet purchase faucet brand recommendation
Franca faucet, a well-known brand of global kitchen and bathroom, is expensive
What, the decoration still uses his own money? ! The Qi family is decorated in installments, with an ultra-low annual interest rate of 3.55% and a maximum loan of 1 million. Apply now to enjoy the discount
If you are interested in brand cooperation, content cooperation, and advertising of this website, please send an email to :.
Toilet
Glass clamp is so common to see in modern glass door system. Only a simple round glass cutout that shows its convenient both for glass supplier and user. To adapt practical application in the development of construction, a variety design of glass clamp emerges, such as straight line edge, bevel line edge, semi-round shape etc. Also different material available, which greatly enrich the style. JIANGYI has specialized in glass door clamp since 2000, our glass clip could pass 24 hours neutral salt spraying test and acid spraying test. Welcome for your consulting.
Specification
1. Material: Brass/ Stainless Steel/ Zinc. Alloy
2. Finish: Mirror / Matt / Antique/ Red copper / Gold / Rose gold
3. Suitable for glass thickness: 8-10mm, 6mm/ 12mm
4. Load weight: 45kgs
5. Must be tempered glass
Glass Clamp,Glass Brackets Clamps ,Stainless Steel Glass Clamps,Glass Shelf Clamps
Jiangyi Industrial Co., Ltd , https://www.cnjyhardware.com